Colossus

Purpose and origins

The Colossus computers were used to help decipher intercepted radio teleprinter messages that had been encrypted using an unknown device. Intelligence information revealed that the Germans called the wireless teleprinter transmission systems "Sägefisch" (sawfish). This led the British to call encrypted German teleprinter traffic "Fish", and the unknown machine and its intercepted messages "Tunny" (tunafish).

Before the Germans increased the security of their operating procedures, British cryptanalysts diagnosed how the unseen machine functioned and built an imitation of it called "British Tunny".

It was deduced that the machine had twelve wheels and used a Vernam ciphering technique on message characters in the standard 5-bit ITA2 telegraph code. It did this by combining the plaintext characters with a stream of key characters using the XOR Boolean function to produce the ciphertext.

In August 1941, a blunder by German operators led to the transmission of two versions of the same message with identical machine settings. These were intercepted and worked on at Bletchley Park. First, John Tiltman, a very talented GC&CS cryptanalyst, derived a keystream of almost 4000 characters. Then Bill Tutte, a newly arrived member of the Research Section, used this keystream to work out the logical structure of the Lorenz machine. He deduced that the twelve wheels consisted of two groups of five, which he named the χ (chi) and ψ (psi) wheels, the remaining two he called μ (mu) or "motor" wheels. The chi wheels stepped regularly with each letter that was encrypted, while the psi wheels stepped irregularly, under the control of the motor wheels.

With a sufficiently random keystream, a Vernam cipher removes the natural language property of a plaintext message of having an uneven frequency distribution of the different characters, to produce a uniform distribution in the ciphertext. The Tunny machine did this well. However, the cryptanalysts worked out that by examining the frequency distribution of the character-to-character changes in the ciphertext, instead of the plain characters, there was a departure from uniformity which provided a way into the system. This was achieved by "differencing" in which each bit or character was XOR-ed with its successor. After Germany surrendered, allied forces captured a Tunny machine and discovered that it was the electromechanical Lorenz SZ (Schlüsselzusatzgerät, cipher attachment) in-line cipher machine.

Decryption processes

By using differencing and knowing that the psi wheels did not advance with each character, Tutte worked out that trying just two differenced bits (impulses) of the chi-stream against the differenced ciphertext would produce a statistic that was non-random. This became known as Tutte's "1+2 break in". It involved calculating the following Boolean function:

Δ

Z

1

⊕

Δ

Z

2

⊕

Δ

χ

1

⊕

Δ

χ

2

=

∙

{\displaystyle \Delta Z_{1}\oplus \Delta Z_{2}\oplus \Delta \chi _{1}\oplus \Delta \chi _{2}=\bullet }

and counting the number of times it yielded "false" (zero). If this number exceeded a pre-defined threshold value known as the "set total", it was printed out. The cryptanalyst would examine the printout to determine which of the putative start positions was most likely to be the correct one for the chi-1 and chi-2 wheels.

This technique would then be applied to other pairs of, or single, impulses to determine the likely start position of all five chi wheels. From this, the de-chi (D) of a ciphertext could be obtained, from which the psi component could be removed by manual methods. If the frequency distribution of characters in the de-chi version of the ciphertext was within certain bounds, "wheel setting" of the chi wheels was considered to have been achieved, and the message settings and de-chi were passed to the "Testery". This was the section at Bletchley Park led by Major Ralph Tester where the bulk of the decrypting work was done by manual and linguistic methods.

Design and construction

Colossus was developed for the "Newmanry", the section headed by the mathematician Max Newman that was responsible for machine methods against the twelve-rotor Lorenz SZ40/42 on-line teleprinter cipher machine (code-named Tunny, for tunafish). The Colossus design arose out of a parallel project that produced a less-ambitious counting machine dubbed "Heath Robinson". Although the Heath Robinson machine proved the concept of machine analysis for this part of the process, it had serious limitations. The electro-mechanical parts were relatively slow and it was difficult to synchronise two looped paper tapes, one containing the enciphered message, and the other representing part of the keystream of the Lorenz machine. Also the tapes tended to stretch and break when being read at up to 2000 characters per second.

Tommy Flowers MBE was a senior electrical engineer and Head of the Switching Group at the Post Office Research Station at Dollis Hill. Prior to his work on Colossus, he had been involved with GC&CS at Bletchley Park from February 1941 in an attempt to improve the Bombes that were used in the cryptanalysis of the German Enigma cipher machine. He was recommended to Max Newman by Alan Turing, who had been impressed by his work on the Bombes. The main components of the Heath Robinson machine were as follows.

A tape transport and reading mechanism that ran the looped key and message tapes at between 1000 and 2000 characters per second.

A combining unit that implemented the logic of Tutte's method.

A counting unit that had been designed by C. E. Wynn-Williams of the Telecommunications Research Establishment (TRE) at Malvern, which counted the number of times the logical function returned a specified truth value.

Flowers had been brought in to design the Heath Robinson's combining unit. He was not impressed by the system of a key tape that had to be kept synchronised with the message tape and, on his own initiative, he designed an electronic machine which eliminated the need for the key tape by having an electronic analogue of the Lorenz (Tunny) machine. He presented this design to Max Newman in February 1943, but the idea that the one to two thousand thermionic valves (vacuum tubes and thyratrons) proposed, could work together reliably, was greeted with great scepticism, so more Robinsons were ordered from Dollis Hill. Flowers, however, knew from his pre-war work that most thermionic valve failures occurred as a result of the thermal stresses at power-up, so not powering a machine down reduced failure rates to very low levels. Additionally, if the heaters were started at a low voltage then slowly brought up to full voltage, thermal stress was reduced. The valves themselves could be soldered-in to avoid problems with plug-in bases, which could be unreliable. Flowers persisted with the idea and obtained support from the Director of the Research Station, W Gordon Radley.

Operation

The Newmanry was staffed by cryptanalysts, operators from the Women's Royal Naval Service (WRNS) – known as "Wrens" – and engineers who were permanently on hand for maintenance and repair. By the end of the war the staffing was 272 Wrens and 27 men.

The first job in operating Colossus for a new message was to prepare the paper tape loop. This was performed by the Wrens who stuck the two ends together using Bostik glue, ensuring that there was a 150-character length of blank tape between the end and the start of the message. Using a special hand punch they inserted a start hole between the third and fourth channels 2+1⁄2 sprocket holes from the end of the blank section, and a stop hole between the fourth and fifth channels 1+1⁄2 sprocket holes from the end of the characters of the message. These were read by specially positioned photocells and indicated when the message was about to start and when it ended. The operator would then thread the paper tape through the gate and around the pulleys of the bedstead and adjust the tension. The two-tape bedstead design had been carried on from Heath Robinson so that one tape could be loaded whilst the previous one was being run. A switch on the Selection Panel specified the "near" or the "far" tape.

After performing various resetting and zeroizing tasks, the Wren operators would, under instruction from the cryptanalyst, operate the "set total" decade switches and the K2 panel switches to set the desired algorithm. They would then start the bedstead tape motor and lamp and, when the tape was up to speed, operate the master start switch.

Programming

Howard Campaigne, a mathematician and cryptanalyst from the US Navy's OP-20-G, wrote the following in a foreword to Flowers' 1983 paper "The Design of Colossus".My view of Colossus was that of cryptanalyst-programmer. I told the machine to make certain calculations and counts, and after studying the results, told it to do another job. It did not remember the previous result, nor could it have acted upon it if it did. Colossus and I alternated in an interaction that sometimes achieved an analysis of an unusual German cipher system, called "Geheimschreiber" by the Germans, and "Fish" by the cryptanalysts.

Colossus was not a stored-program computer. The input data for the five parallel processors was read from the looped message paper tape and the electronic pattern generators for the chi, psi and motor wheels. The programs for the processors were set and held on the switches and jack panel connections. Each processor could evaluate a Boolean function and count and display the number of times it yielded the specified value of "false" (0) or "true" (1) for each pass of the message tape.

Input to the processors came from two sources, the shift registers from tape reading and the thyratron rings that emulated the wheels of the Tunny machine. The characters on the paper tape were called Z and the characters from the Tunny emulator were referred to by the Greek letters that Bill Tutte had given them when working out the logical structure of the machine. On the selection panel, switches specified either Z or ΔZ, either

χ

{\displaystyle \chi }

or Δ

χ

{\displaystyle \chi }

and either

ψ

{\displaystyle \psi }

or Δ

ψ

{\displaystyle \psi }

Influence and fate

Although the Colossus was the first of the electronic digital machines with programmability, albeit limited by modern standards, it was not a general-purpose machine, being designed for a range of cryptanalytic tasks, most involving counting the results of evaluating Boolean algorithms.

A Colossus computer was thus not a fully Turing complete machine. However, University of San Francisco professor Benjamin Wells has shown that if all ten Colossus machines made were rearranged in a specific cluster, then the entire set of computers could have simulated a universal Turing machine, and thus be Turing complete.

Colossus and the reasons for its construction were highly secret and remained so for 30 years after the War. Consequently, it was not included in the history of computing hardware for many years, and Flowers and his associates were deprived of the recognition they were due. All but two of the Colossi were dismantled after the war and parts returned to the Post Office. Some parts, sanitised as to their original purpose, were taken to Max Newman's Royal Society Computing Machine Laboratory at Manchester University. Two Colossi, along with two Tunny machines, were retained and moved to GCHQ's new headquarters at Eastcote in April 1946, and then to Cheltenham between 1952 and 1954. One of the Colossi, known as Colossus Blue, was dismantled in 1959; the other in the 1960s. Tommy Flowers was ordered to destroy all documentation. He duly burnt them in a furnace and later said of that order:

That was a terrible mistake. I was instructed to destroy all the records, which I did. I took all the drawings and the plans and all the information about Colossus on paper and put it in the boiler fire. And saw it burn. The Colossi were adapted for other purposes, with varying degrees of success; in their later years they were used for training. Jack Good related how he was the first to use Colossus after the war, persuading the US National Security Agency that it could be used to perform a function for which they were planning to build a special-purpose machine. Colossus was also used to perform character counts on one-time pad tape to test for non-randomness.

A small number of people who were associated with Colossus—and knew that large-scale, reliable, high-speed electronic digital computing devices were feasible—played significant roles in early computer work in the UK and probably in the US. However, being so secret, it had little direct influence on the development of later computers; it was EDVAC that was the seminal computer architecture of the time. In 1972, Herman Goldstine, who was unaware of Colossus and its legacy to the projects of people such as Alan Turing (ACE), Max Newman (Manchester computers) and Harry Huskey (Bendix G-15), wrote that,

Reconstruction

A team led by Tony Sale built a fully functional reconstruction of a Colossus Mark 2 between 1993 and 2008. In spite of the blueprints and hardware being destroyed, a surprising amount of material had survived, mainly in engineers' notebooks, but a considerable amount of it in the U.S. The optical tape reader might have posed the biggest problem, but Dr. Arnold Lynch, its original designer was able to redesign it to his own original specification. The reconstruction is on display, in the historically correct place for Colossus No. 9, at The National Museum of Computing, in H Block Bletchley Park in Milton Keynes, Buckinghamshire.

In November 2007, to celebrate the project completion and to mark the start of a fundraising initiative for The National Museum of Computing, a Cipher Challenge pitted the rebuilt Colossus against radio amateurs worldwide in being first to receive and decode three messages enciphered using the Lorenz SZ42 and transmitted from radio station DL0HNF in the Heinz Nixdorf MuseumsForum computer museum. The challenge was easily won by radio amateur Joachim Schüth, who had carefully prepared for the event and developed his own signal processing and code-breaking code using Ada. The Colossus team were hampered by their wish to use World War II radio equipment, delaying them by a day because of poor reception conditions. Nevertheless, the victor's 1.4 GHz laptop, running his own code, took less than a minute to find the settings for all 12 wheels. The German codebreaker said: "My laptop digested ciphertext at a speed of 1.2 million characters per second—240 times faster than Colossus. If you scale the CPU frequency by that factor, you get an equivalent clock of 5.8 MHz for Colossus. That is a remarkable speed for a computer built in 1944."

The Cipher Challenge verified the successful completion of the rebuilding project. "On the strength of today's performance Colossus is as good as it was six decades ago", commented Tony Sale. "We are delighted to have produced a fitting tribute to the people who worked at Bletchley Park and whose brainpower devised these fantastic machines which broke these ciphers and shortened the war by many months."

Other meanings

There was a fictional computer named Colossus in the 1970 film Colossus: The Forbin Project which was based on the 1966 novel Colossus by D. F. Jones. This was a coincidence as it pre-dates the public release of information about Colossus, or even its name.

Neal Stephenson's novel Cryptonomicon (1999) also contains a fictional treatment of the historical role played by Turing and Bletchley Park.

The Colossus is the world's largest AI supercomputer.